Triggered irrigation for bare soil

A discussion forum for Hydrus-1D users.
Post Reply
Koji
Posts: 3
Joined: Wed Jan 13, 2021 6:25 am
Location: Japan

Triggered irrigation for bare soil

Post by Koji » Wed Jan 13, 2021 8:05 am

Hello
I am Koji.
I am facing on a trouble in triggered irrigation for bare soil using Hydrus-1D ver. 4.17.
Evaporation data given a constant value in variable boundary condition is automatically been 0 cm/h after the first irrigation using triggered irrigation mode.

The condition of the project is as follows;
Soil type: Sand
Soil length: 100 cm
Length unit = cm
Time unit: hr
Initial time= 0 hr, Final time= 48hr
Upper boundary condition: Atmospheric BC with surface run off
Variable boundary condition: Precipitation = 0; Evaporation rate 0.03 cm/h; hCritA=100000
This condition is continued for 48 hrs.
Bottom boundary condition: Free drainage

Triggered irrigation condition
Observation point = 1 (at the point of a 1-cm deep)
Pressure head triggering irrigation = -100 cm
Irrigation rate = 0.25 cm/h
Irrigation duration=1 hr
Lag time= 0
Initial condition of all nodes = - 50 cm
I think that triggered irrigation was conducted because irrigation is repeated when the threshold was changed into -50 cm. However, the rTop in the T_Level.out are changed from 0.03 cm/h to 0 cm/h after the first irrigation.

I want to know how to solve this trouble. Please give me any advice.

Jirka
Posts: 5111
Joined: Sat Mar 16, 2002 3:47 pm
Location: USA
Location: Riverside, CA

Re: Triggered irrigation for bare soil

Post by Jirka » Wed Jan 13, 2021 9:34 pm

I must have already fixed that in my latest files since I do not see this behavior. Replace the attached file (note that this is 64-bit exe). J.
Attachments
TrIrrig.rar
(42 KiB) Downloaded 6 times
h1d_calc.rar
(287.3 KiB) Downloaded 9 times

Koji
Posts: 3
Joined: Wed Jan 13, 2021 6:25 am
Location: Japan

Re: Triggered irrigation for bare soil

Post by Koji » Thu Jan 14, 2021 5:43 am

Dear Jirka

Thank you for your quick reply.
However this problem has not resolved yet. I run your project using my HD-1D. As result, rTop become 0 after the first irrigation. When I have checked T_Level.out before running the project, rTop is return to 0.1 after the first irrigation. I attached the results.
Moreover, I replaced the h1d_calc.exe which you send me. Then HD-1D don't run.
Attachments
TrIrrig_koji.zip
(43.32 KiB) Downloaded 5 times

Jirka
Posts: 5111
Joined: Sat Mar 16, 2002 3:47 pm
Location: USA
Location: Riverside, CA

Re: Triggered irrigation for bare soil

Post by Jirka » Thu Jan 14, 2021 9:26 pm

Perhaps, I should have posted the 32 bit version of the file. J.
Attachments
h1d_calc.rar
(243.55 KiB) Downloaded 7 times

Koji
Posts: 3
Joined: Wed Jan 13, 2021 6:25 am
Location: Japan

Re: Triggered irrigation for bare soil

Post by Koji » Fri Jan 15, 2021 11:49 am

Although The file size of h1d_calc.exe in ver4.17 is 1262KB, your file is 643KB.Can I replace them?

Jirka
Posts: 5111
Joined: Sat Mar 16, 2002 3:47 pm
Location: USA
Location: Riverside, CA

Re: Triggered irrigation for bare soil

Post by Jirka » Fri Jan 15, 2021 8:09 pm

Obviously, make a back up first so that you can return to the original file if needed. J.

Post Reply